NINVA 凝华北京凝华科技有限公司

WAFER BOAT

Wafer boats process and equipment solution

Wafer-boat machining connects integral or separate structures, supporting faces, repeated slots and assembly relationships through traceable full-length datums. Check whole-part and local machining space first, then coordinate datum grinding, segmented slot machining, process inspection and wheel-dressing feedback, followed by edge finishing, required assembly, cleaning and full-length acceptance. NINVA equipment combinations are limited to validated accessible operations and the supporting wheel line.

Silicon carbide · SiCQuartzSiC-coated graphite
Explore all part solutions
SiC / QUARTZ

DRAWING REQUIREMENTS

Translate drawing requirements into process targets.

Drawing requirement examples

Use these examples to define selection and validation criteria. Confirm actual targets against the customer drawing, material and inspection method.

Slot-pitch tolerance
±0.05 mm
Accumulated error across 100 slots
≤0.3 mm
Slot-width tolerance
±0.05 mm
Slot depth
8–15 mm
Straightness
<0.5 mm/m

Inputs for the process solution

Material & construction
Specify the grade, integral or assembled construction, coating and incoming condition.
Overall size & workholding
Provide length, envelope dimensions, support, fixture space and machining direction.
Complete slot specification
Specify slot count, pitch, width, depth, bottom geometry and opening structure.
Datum & accumulated requirements
Define individual-slot requirements, accumulated error, straightness relationships and inspection datums.
Edges, surfaces & output
State edge-chipping and surface requirements, inspection methods, dressing arrangements and target output.

MACHINING CHALLENGES

Identify the challenge. Define the process control.

01

Separate whole-part, component and machining envelopes

A wafer boat may enter machining as an integral, column-type or separately assembled structure. Check whole-part/component, fixture and tool envelopes and machining direction before assigning whole-part or specific local operations to a machine.

02

Control repeated-slot spacing and full-length accumulation separately

An acceptable individual slot does not establish a full-length pattern. Define slot identifiers, first/reference slots, segment transfers and full-length inspection datums, recording individual-slot, adjacent-slot and cumulative-position results separately.

03

Coordinate deep/narrow-slot access and edge integrity

Review slot width/depth, opening direction and support together with wheel construction. Use representative slots to validate tool access, edges and operation sequence before defining the repeatable machining scope.

04

Connect wheel condition, process inspection and dressing

Link slot identifiers, wheel condition and process checks during repeated machining. Remeasure after dressing under agreed inspection/dressing triggers, avoiding first-slot-only acceptance or treating wheel dressing as a component-machining operation.

05

Link segment, assembly and final full-length condition

Segment location, edge finishing, coating condition or assembly can change the final inspection condition. Link local results to assembly/full-length datums and accept the cleaned part in its final delivery condition.

COMPLETE PROCESS CHAIN

From incoming part to final acceptance.

Integral/separate blank → machining space & datums → local supporting features → segmented slot grinding → between-slot checks/wheel feedback → edges & assembly → cleaning & full-length acceptance

NINVA machine operationsCustomer / supporting process interfaces
  1. 01Prepare integral or component blanks
  2. 02Grind accessible datums & support faces
  3. 03Grind local profiles & support structures
  4. 04Grind repeated slots in defined sections
  5. 05Between-slot process checks & dressing feedback
  6. 06Finish edges & assemble structures
  7. 07Cleaning & full-length acceptance
  1. 01
    Customer / supporting process interface

    Prepare integral or component blanks

    Allocate stock against integral or assembled construction, material and incoming condition, retaining datums for support, assembly and slot operations.

    Purpose
    Identify construction and incoming condition before using any local dimension to judge the complete machining envelope.
    Operation output
    Blanks with allocated machining stock and locating arrangements
    Inspection items
    Check material, overall envelope, component sizes, stock and subsequent machining directions.
    Handover conditions
    Transfer integral/component drawings, material/coating condition, incoming envelope, local allowances and assembly/support arrangements.
  2. 02
    Operation supported by NINVA equipment

    Grind accessible datums & support faces

    For integral parts or components that fit the machine space, assess NHM-series grinding of datum and support faces to establish subsequent operation locations.

    The integral part or component, fixture and tool envelope must fit the selected model’s working space.

    Purpose
    Establish reusable datums within confirmed working space before relating slots and supporting structures to them.
    Operation output
    Validated locating surfaces for subsequent structural operations
    Inspection items
    Inspect locating surfaces, support relationships and datum consistency after repeated setups.
    Handover conditions
    Transfer locating/supporting faces, machining direction, workholding, repeat-location and segment-transfer records.
  3. 03
    Operation supported by NINVA equipment

    Grind local profiles & support structures

    Grind local profiles, support and assembly structures within the validated scope, considering machining direction and tool access.

    Define the machining scope against actual material, geometry, workholding and tooling conditions.

    Purpose
    Local contours/supports must provide defined interfaces for slot machining and later assembly.
    Operation output
    Structures with the specified local mechanical features machined
    Inspection items
    Inspect local dimensions, positions, edges and their relationship to the overall datums.
    Handover conditions
    Transfer local dimensions, support/assembly relationships, edge condition and access to each slot region.
  4. 04
    Operation supported by NINVA equipment

    Grind repeated slots in defined sections

    Grind accessible slot features while coordinating datum changes, wheel condition and in-process checks for repeated operations. Validate local samples and whole-part operations separately.

    Slot width, depth, tool access and workholding length must satisfy project-specific validation conditions.

    Purpose
    Expand repeated machining only after datum and representative-slot validation, maintaining consistency through slot and segment records.
    Operation output
    Validated slot features with process records
    Inspection items
    Inspect individual-slot dimensions, inter-slot relationships, edges and accumulated requirements within the machined range.
    Handover conditions
    Transfer slot identifiers, machining order, tool/wheel condition, individual-slot results and locations requiring process inspection.
  5. 05
    Customer / supporting process interface

    Between-slot process checks & dressing feedback

    At project-agreed checkpoints, inspect slot dimensions, spacing, edges and wheel condition together. Where dressing is required, return to the separate wheel-support line; remeasure an agreed representative slot after dressing before continuing the next segment.

    Purpose
    Process checks create feedback between repeated machining and wheel dressing rather than deferring all assessment until the entire part is completed.
    Operation output
    Process-check results linked to slot identifiers, wheel condition and operation adjustments
    Inspection items
    Inspect individual slots, adjacent spacing and cumulative position within the current segment by agreed drawing-based methods.
    Handover conditions
    Transfer checkpoints, slot identifiers, dressing triggers and post-dressing remeasurement, with defined conditions for resuming machining.
  6. 06
    Customer / supporting process interface

    Finish edges & assemble structures

    Coordinate validated local operations with the customer’s or supporting operations’ edge finishing, other structural machining and component assembly.

    Plan edge finishing, required assembly and coating-stage handovers against the customer drawing; local grinding does not automatically cover all downstream whole-part operations.

    Purpose
    Edge finishing and required assembly connect local machining results to the final full-length structure, retaining datum traceability.
    Operation output
    An integral or assembled structure after the agreed subsequent operations
    Inspection items
    Inspect edges, assembly relationships, location and records of stock transfer between operations.
    Handover conditions
    Transfer edge, assembly and support records and the locating method for full-length inspection.
  7. 07
    Customer / supporting process interface

    Cleaning & full-length acceptance

    Coordinate cleaning and whole-part inspection against customer procedures, linking individual-slot, sectional, assembly and full-length results. Define whole-part machining and acceptance scope through project-specific validation.

    Purpose
    Combine slot, segment and full-length results in the final assembly/delivery condition without extrapolating from a local sample.
    Operation output
    Process records linking local and overall acceptance
    Inspection items
    Inspect slot pitch and accumulated requirements, overall locating relationships, surfaces and cleanliness against the drawing.
    Handover conditions
    Transfer cleaning records, slot/cumulative-position maps, assembly relationships and agreed full-length acceptance results.

GRINDING SUPPORT

Wheel production and dressing support component grinding.

Profiled-wheel production & dressing

Where component grinding uses suitable electrically conductive metal-bond diamond or CBN profiled wheels, assess the SL25L / SL30 for wheel-profile production, dressing and worn-profile restoration. This supporting operation acts on the wheel and is coordinated separately with component grinding and measurement results.

EQUIPMENT COMBINATIONS

Combine equipment around the machining task.

01

Accessible local-structure & repeated-slot grinding combination

For an integral part or component within machine space, with validated access to specified supports, local contours or slots.

NINVA equipment and roles

Component grinding: establish datums and machine specified local structures/slots within confirmed envelope, orientation and workholding scope.

Separate wheel line: produce/dress suitable conductive metal-bond profiled wheels, coordinated with slot remeasurement.

Customer and supporting operations

  • Coordinate operations beyond machine envelope/access, required assembly, finishing, cleaning and full-length acceptance through customer/supporting routes.

Combination validation priorities

  • Validate the part/component plus fixture/tool envelope; do not infer whole-part capability from travel specifications.
  • Validate representative slots and segment transfers first; assess individual-slot, between-slot and full-length results separately.
02

Wheel-support combination for an existing grinding line

For an existing wafer-boat/support-component grinding line requiring applicable profile-wheel production, dressing and process coordination.

NINVA equipment and roles

Supporting wheel equipment: acts on applicable wheels for profile production, dressing and restoration; it does not machine the wafer boat itself.

Customer and supporting operations

  • Coordinate the customer’s grinding equipment, wheel mounting/profile inspection and component process inspection.

Combination validation priorities

  • Confirm wheel material, conductive bond, mounting interface, target profile and current wear condition.
  • Relate pre-/post-dressing wheel profile to representative-slot machining and remeasurement results.
View the function and conditions of each machine type

Validate supports, local contours and representative slots within confirmed envelope/access limits, assessing individual-slot, segment and whole-part results separately.

For assessing profile production and dressing of suitable electrically conductive metal-bond wheels, supporting grinding trials on slots or support features.

VALIDATION & HANDOVER

Connect the process chain through inspection and handover records.

Validation itemInspection methodHandover record
Whole-part/local machining spaceCheck integral/component, fixture, tool and machining orientation to define machine responsibility.Working-envelope drawing, support/clamping arrangement and accessible-feature list.
Common datums & segment transfersUse one datum chain for locating faces, support, first/reference slots and segment transfers.Datum definition, repeated-setup and segment-location records.
Individual-slot & between-slot resultsInspect width/depth, edges and between-slot positions by slot identifier at agreed checkpoints.Slot map, individual results, process changes and stage cumulative-position records.
Wheel-dressing feedbackRecord wheel profile/dressing conditions and remeasure an agreed representative slot after dressing.Wheel/slot linkage, dressing triggers, pre-/post-dressing results and restart criteria.
Assembly, cleaning & full-length acceptanceAssess individual-slot, segment and full-length criteria separately in the final structure/support condition.Assembly/cleaning records, full-length position map and final acceptance results.

Prepare these inputs for the process discussion

  1. Integral/column/component drawings, material/coating condition and whole-part/local envelope dimensions.
  2. Slot identifiers/count, width/depth, spacing, reference slots and full-length cumulative requirements.
  3. Workholding, support, machining orientation, segment transfers and required assembly method.
  4. Current wheel specification/bond/profile, dressing and slot process-inspection records.
  5. Final full-length inspection, cleaning/delivery condition and exact operations assigned to the proposed equipment.

VALIDATE YOUR MACHINE SELECTION

Bring the drawing. Define the machine solution.

Share the part, material, critical requirements and output objectives to discuss candidate machines, trials and configuration.

An account manager responds within 24 hours. Trials generally take 3–20 days; an NDA is available.